Send SMS
Contact Us

Module For Arduino

DTMF Decoder Module MT8870

DTMF Decoder Module MT8870

Approx. Rs 150 / Piece

The MT8870 Tone Decoder is a kind of common used multifrequency decode IC product developed by the MITEL company. It is a compete DTMF receiver. After it received the DTMF signal, it will divide the signal into high frequency group and low frequency group and send the signal to the digital decoder which can figure out the key value then send it to the outside Bus via four lines( Q1, Q2, Q3, Q4) as the binary form.

Features:

ISD1760 - Voice Recording Module

ISD1760 - Voice Recording Module

Approx. Rs 400 / Piece


Specifications:

ISD1820 - Voice Recorder

ISD1820 - Voice Recorder

Approx. Rs 175 / Piece

This voice record/playback device is based on ISD1820 chip, which can record/playback multiple-message. It can offer true single-chip voice recording, non-volatile storage, and playback capability for 8 to 20 seconds. For the sampling rate of 3.2KHz it can record for the total duration of 20 seconds.

Feature:

If you want change the record duration, an external resistor is necessary to select the record duration and sampling frequency, which can range from 8 – 20 seconds (4-12kHz sampling frequency). This voice record module provides default connect to a 100k resistor through P2 by short cap. So the default record duration is 10s.

TM1638 8 Bit Button LED Segment Digital Control

TM1638 8 Bit Button LED Segment Digital Control

Approx. Rs 200 / Piece

Use TM1638 digital tube drive chip to drive common cathode LED digital tube.

This module for the chip TM1638, set the above three kinds of single chip microcomputer common peripheral circuit, the biggest characteristic is to simply take microcontroller three IO mouth can drive, scanning display and key scan don't need microcontroller intervention, only need to register to display data related to reading and writing or testing buttons, save MCU resources.

Features:

4 Channel 5v Relay Board

4 Channel 5v Relay Board

Approx. Rs 175 / Piece

Description:

This is a 5V 4-Channel Relay interface board, Be able to control various appliances, and other equipments equipment with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).

5V USB Power PAM8403 Mini Digital Audio Amplifier Board

5V USB Power PAM8403 Mini Digital Audio Amplifier Board

Approx. Rs 80 / Piece

Technical Specifications:Note: Do not mix the "negative" of the left and the right output channel with "negative" of the power supply, otherwise it will burn the IC.

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain

Approx. Rs 300 / Piece

ADS1015 12-Bit ADC - 4 Channel with Programmable Gain Amplifier

For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1015 provides 12-bit precision at 3300 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 12 bit converter.

 

Technical details

ADS1115 ADC 4 Channel 16Bit I2C PGA Low Power Modules for Arduino

ADS1115 ADC 4 Channel 16Bit I2C PGA Low Power Modules for Arduino

Approx. Rs 300 / Number


For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter.

 

Technical details

Additional Information:

Arduino Compatible 360 Degree Rotating Rotary Encoder Module

Arduino Compatible 360 Degree Rotating Rotary Encoder Module

Approx. Rs 100 / Piece

Description:

Rotation of the rotary encoder may be counted by the positive rotation direction and a reverse direction pulse frequency output during rotation potentiometer not count this rotation count is not limited. With buttons on the rotary encoder can be reset to the initial state, that starts counting from 0.

Specifications
General
Model: Keyes KY-040
- Material: Glass fiber + plastic + iron
- Compatibility: Ardunio
Electronic Components
Architecture: Arduino
- Operating Voltage: 5V
Weight and Size
Product Weight: 5 g
- Package Weight: 0.055 kg
- Package Size(L x W x H): 7.0 x 5.0 x 2.0 cm
Package Contents
Package Contents: 1 x Module

Rotation of the rotary encoder may be counted by the positive rotation direction and a reverse direction pulse frequency output during rotation potentiometer not count this rotation count is not limited. With buttons on the rotary encoder can be reset to the initial state, that starts counting from 0

DS1307 I2C Real Time Clock Module

DS1307 I2C Real Time Clock Module

Approx. Rs 100 / Piece

DS1307 is a real-time chip of DALLAS company,which adopt I2C protocal to communicate with SCM, and there was this kind interface on Arduino, therefore is very convenient to link with each other. DS1307 have a programmable waveforms output, it can be used to drive LED lights, or trigger a certain event as a break off, but be careful when you use it to take some kind of high power module. We design the real clock module to pin out the I2C interface of Ds1307 and programmable waveforms output interface SQW are connected, but usually we will only use the I2C interface to realize basic set the clock/read function. Note, this module must be installed on the battery can work normally. The battery is button batteries (type CR2032 will be better), the positive upward:

This tiny module embraces DS1307 time module, DS18B20 temperature module and AT24C32 storage module. DS1307 and AT24C32 are connected to IIC bus. And DS18B20 can be visited via DS pin.

Feature :

1 Power supply: 5V DC and Button Battery

2 Interface: IIC

3 Size: 16mm * 22mm * 23mm ???Almost same size as CR2032 Button Battery???

4 Memory Capacity : 32K bit

5 IC: DS1307,DS18B20,AT24C32 ; DS1307 and AT24C32 can be used separately

6 Have the automatic adjustment function of second minute day month and year

7 Take alarm output function and cut off power protection function

ENC28J60 Ethernet LAN Network Module for Arduino

ENC28J60 Ethernet LAN Network Module for Arduino

Approx. Rs 275 / Piece

Specifications:

Easy Driver Stepper Motor Driver V44 A3967 for Arduino

Easy Driver Stepper Motor Driver V44 A3967 for Arduino

Approx. Rs 200 / Piece

Specification:

Joystick Module

Joystick Module

Approx. Rs 80 / Piece

Product Description

This is a Joystick module that has X,Y analog outputs and has a switch that detects button press. The joystick is made up of two passive potentio-meters (variable resistors) and a push button and therefore can be used at any standard voltage levels.

Applications

Max7219 Dot Matrix Module for Arduino

Max7219 Dot Matrix Module for Arduino

Approx. Rs 175 / Piece

Features:

Micro SD Card Module for Arduino

Micro SD Card Module for Arduino

Approx. Rs 80 / Piece


Description:-

To use with an Arduino, connect GND to ground, 5V to 5V, CLK to pin 13, DO to pin 12, DI to pin 11, and CS to pin 10. Then you can use the Arduino IDE's SD library which supports FAT and FAT32 SD cards

NE555 Pulse Frequency Duty Cycle Adjustable Module

NE555 Pulse Frequency Duty Cycle Adjustable Module

Approx. Rs 150 / Piece(s)

Features:-

The output frequency is adjustable:

Nokia 5110 LCD

Nokia 5110 LCD

Approx. Rs 200 / Piece

Product Description

These displays were used in old Nokia 5110/3310 cell phones (before the smart-phone fad turned every cell phone into a TV). It’s a 84×48 pixel monochrome LCD display. These displays are small, only about 1.5″ diagonal, but very readable and come with a white backlight. This display is made of 84×48 individual pixels, so you can use it for graphics, text or bitmaps. These displays are inexpensive, easy to use, require only a few digital I/O pins and are fairly low power as well
To drive the display, you will need 3 to 5 digital output pins (depending on whether you want to manually control the chip select and reset lines). Another pin can be used to control (via on/off or PWM) the backlight – the backlight LEDs are wired to a transistor.

The display driver is a PCD8544 chip, and it runs at 3.3V so you’ll need a 3V supply handy (you don’t need that much current though, maybe 10mA tops). Logic levels must be 3V to prevent damage but we include a free level shifter chip so you can easily connect it to 5V logic such as an Arduino.

Specifications of LCD 5110

Feature:

OV7670 Camera Module

OV7670 Camera Module

Approx. Rs 300 / Piece

Description: This Module uses OV7670 image sensor, which is small in volume, works at low operating voltage, and provides all functions of a single chip VGA camera and image processor. Through SCCB bus control, the sensor can output the whole frame, sampling, and various resolution of 8 bits of data. The product VGA image can reach up to a maximum of 30 frames per second. Users can completely control the image quality, data format and transmission mode. All the process of image processing functions can be through the SCCB programming interface, including gamma curve, white balance, saturation and chroma .

The OV7670 is a low cost image sensor DSP that can operate at a maximum of 30 fps and 640 x 480 ("VGA") resolutions, equivalent to 0.3 Megapixels. The captured image can be pre-processed by the DSP before sending it out. This preprocessing can be configured via the Serial Camera Control Bus (SCCB). The datasheet has protocol.
In addition, OmmiVision image sensor has been in application of unique sensor technology, by reducing or eliminating the optical or electronic defect such as fixed pattern noise, tail, floating away, etc., to improve the quality of the image, and get the clear and stable color images.

Features:


Additional Information:

PAM8403 mini 5V Amplifier Board with Switch Potentiometer

PAM8403 mini 5V Amplifier Board with Switch Potentiometer

Approx. Rs 100 / Piece

Description:


Feature:


Note:-Working voltage should not exceed 5.5V, the power of positive and negative can not be wrong. Otherwise, there is the possibility of damage chip

PCA9685 16-Channel 12-Bit PWM Servo Driver

PCA9685 16-Channel 12-Bit PWM Servo Driver

Approx. Rs 250 / Piece

Features


Technical Details

Introduction
PCA9685 16-Channel 12-Bit PWM Servo Driver can help a lot when there are insufficient PWM output pins for the MCU in your project. The only condition is that the main control chip supports I2C communication, which means enabling the communication between the chip and PCA9685, so as to control multiple servos simultaneously.

TM1637 Based 4 Bits Red Digital Tube LED Display Module

TM1637 Based 4 Bits Red Digital Tube LED Display Module

Approx. Rs 150 / Piece

The module comes with four common anode tube (0.36 in.) display with a clock point based on driver IC TM1637. You can use only two signal lines of the MCU to control these four 7-Segment digital tubes.

Features:

X
Provide Us More Details
Is this Requirement:

One Time Regular

How soon do you want this:

Immediate After 1 month

Purpose of Requirement:

Reselling End Use Raw Material

X

Looking for Module For Arduino ?

    country-ico

    We will contact you soon !

    Dileep Jain

    (CEO)

    Rajguru Electronics (I) Private Limited

    Lamington Road, Mumbai, Maharashtra, India

    More Categories

    View All Categories »
    Send SMS
    Contact Us