Send SMS
Contact Us

Sensors For Arduino

Sound Detection Sensor

Sound Detection Sensor

Approx. Rs 80 / Piece


Introduction:The Sound sensor is able to detect different sizes of sound. This sensor can be used to for a variety of uses from industrial to simple hobby or playing around.

Specifications :


These little units can sense sound and variations in sound and interface easily with microcontrollers.
When the ambient sound levels are less than the threshold set by the potentiometer, the output of the unit is High, conversely when the ambient sound levels rise above the pre-set threshold, the modules output is Low.
Adjustable Sensitivity
Output in the form of digital switching outputs (0 and 1 high and low)
Fixed bolt hole for easy installation
Operating voltage : 3.3V-5V
Board size: 3.2cm * 1.7cm

TTP223 Touch Sensor

TTP223 Touch Sensor

Approx. Rs 80 / Piece


Overview:

This is a simple touch sensor module. You can use it to replace a traditional push button. Using the TTP223 touch detector IC It measures the capacitance of a metallic pad. It can detect the change in capacitance when a finger is near it. This is the same technology used in the iPhone touch screen.

This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it still can feel the touch. And the sensetivity well decrease as isolation get thick.

Specifications:

Tap Sensor Module For Arduino

Tap Sensor Module For Arduino

Approx. Rs 125 / Piece

A vibration switch, also called spring switch or shock sensor, is an electronic switch which induces shock force and transfers the result to a circuit device thus triggering it to work. It contains the following parts: conductive vibration spring, switch body, trigger pin, and packaging agent.

37 In 1 Sensor Module Board Set Kit for Arduino

37 In 1 Sensor Module Board Set Kit for Arduino
  • 37 In 1 Sensor Module Board Set Kit for Arduino
  • 37 In 1 Sensor Module Board Set Kit for Arduino
  • 37 In 1 Sensor Module Board Set Kit for Arduino

Approx. Rs 1,200 / Piece


We offer 37 In 1 Sensor Module Board Set Kit for Arduino.

Details:
• Material: Circuit board
• Application:
• Packing list:
• 1 x Small passive buzzer module KY-006
• 1 x 2-color LED module KY-011
• 1 x Hit sensor module KY-031
• 1 x Vibration switch module KY-002
• 1 x Photo resistor module KY-018
• 1 x Key switch module KY-004
• 1 x Tilt switch module KY-020
• 1 x 3-color full-color LED SMD modules KY-009
• 1 x Infrared emission sensor module KY-005
• 1 x 3-color LED module KY-016
• 1 x Mercury open optical module KY-017
• 1 x Yin Yi 2-color LED module 3MM KY-029
• 1 x Active buzzer module KY-012
• 1 x Temperature sensor module KY-013
• 1 x Automatic flashing colorful LED module KY-034
• 1 x Mini magnetic reed modules KY-021
• 1 x Hall magnetic sensor module KY-003
• 1 x Infrared sensor receiver module KY-022
• 1 x Class Bihor magnetic sensor KY-035
• 1 x Magic light cup module KY-027
• 1 x Rotary encoder module KY-040
• 1 x Optical broken module KY-010
• 1 x Detect the heartbeat module KY-039
• 1 x Reed module KY-025
• 1 x Obstacle avoidance sensor module KY-032
• 1 x Hunt sensor module KY-033
• 1 x Microphone sound sensor module KY-038
• 1 x Laser sensor module KY-008
• 1 x 5V relay module KY-019
• 1 x Temperature sensor module KY-001
• 1 x Temperature sensor module KY-028
• 1 x Linear magnetic Hall sensors KY-024
• 1 x Flame sensor module KY-026
• 1 x Sensitive microphone sensor module KY-037
• 1 x Temperature and humidity sensor module KY-015
• 1 x XY-axis joystick module KY•023
• 1 x Metal touch sensor module KY-036
• 1 x Box

Arduino Photoresistor Detection Photosensitive Light Sensor

Arduino Photoresistor Detection Photosensitive Light Sensor

Approx. Rs 80 / Piece

Description:


Interface Description (4-wire):


Color Sensor Recognition TCS230 TCS3200 Module

Color Sensor Recognition TCS230 TCS3200 Module

Approx. Rs 250 / Piece

Color Sensor Recognition TCS230 TCS3200 Module come with programmable color and full-scale output frequency support. Offering direct communication with microcontroller, these also have power down feature, low-profile lead (pb) free and RoHS and compliant surface-mount package. Further, the presence of on-board color sensor support for 3V-5V voltage output and output frequency voltage of 0 - 5V also makes it directly connectable with microcontroller. Some of its standard features include use as programmable color light-to-frequency converters, providing output in form of square wave, scaling of full-scale output frequency to one of three preset values and others.

 

Features:


Additional Information:

Current Sensor ACS712 - 30A

Current Sensor ACS712 - 30A

Approx. Rs 200 / Piece

Specifications:

Note: ACS712 is based on Hall detection principle, please try to avoid the magnetic field, when using as it may impact the reading accuracy.

Current Sensor Module ACS712 - 20A

Current Sensor Module ACS712 - 20A

Approx. Rs 200 / Piece

Specifications:

 

Note: ACS712 is based on Hall detection principle, please try to avoid the magnetic field, when using as it may impact the reading accuracy.

Current Sensor Module ACS712 - 5A

Current Sensor Module ACS712 - 5A

Approx. Rs 200 / Piece

Specifications:

 

Note: ACS712 is based on Hall detection principle, please try to avoid the magnetic field, when using as it may impact the reading accuracy.

ECG Sensor Module - AD8232

ECG Sensor Module - AD8232

Approx. Rs 800 / Packet


This sensor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.

The AD8232 is an integrated signal conditioning block for ECG and other biopotential measurement applications. It is designed to extract, amplify, and filter small biopotential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.

The AD8232 module breaks out nine connections from the IC that you can solder pins, wires, or other connectors to. SDN, LO+, LO-, OUTPUT, 3.3V, GND provide essential pins for operating this monitor with an Arduino or other development board. Also provided on this board are RA (Right Arm), LA (Left Arm), and RL (Right Leg) pins to attach and use your own custom sensors. Additionally, there is an LED indicator light that will pulsate to the rhythm of a heart beat.

Note: This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions.

Features:

EMG Sensor Module For Arduino

EMG Sensor Module For Arduino

Approx. Rs 1,800 / Piece

Through the detection of electromyography (EMG), measuring muscle activity has traditionally been used in medical research, however,Along with the continuously shrinking but more powerful microcontroller and integrated circuit available, EMG electrical road and the sensor can be used for a variety of control system.The sensor will measure the filter, electrical activity of muscle output rectifier 0-Vsvolts, the output depends on the amount of selected muscle activity.Easy to use for Arduino controller detect muscle activity.

 

Power supply voltage:

+-9V dual power supply, the minimum +-3.5V

 

Package Included:

Package included: 1 x EMG Sensor 1 x Professional EMG Cable 3 x Disposable Surface Electrode

Flame Sensor Module

Flame Sensor Module

Approx. Rs 80 / Piece

Flame Sensor Module

The flame sensor module detects wavelengths from 760nm-1100nm. The are other sources of heat that will also detect this wavelength. It is therefore important that you ensure that the only source of this particular range will be the flame that you want to detect.

Features:
- With output instructions
- Single output
- The output valid signal is low
- For the detection wavelength at 760 nm to 1100 nm range of the heat
- The detection angle of 60 degrees
- The output switch circuit boards! (MCU can be connected directly)

Specifications:
- Size: 32 x 11 x 20mm
- Main chip: LM393, infrared receiver
- Operating voltage: DC 3-5V

Lm393 Motor Speed Measuring Sensor Module For Arduino

Lm393 Motor Speed Measuring Sensor Module For Arduino

Approx. Rs 125 / Piece

Application:

Widely used in motor speed detection, pulse count, the position limit, etc.

Feature:


Specification:


The DO output interface can be directly connected to a micro-controller IO port, if there is a block detection sensor, such as the speed of the motor encoder can detect.
DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.

Wiring specification:


Additional Information:

Metal Touch Sensor Module

Metal Touch Sensor Module

Approx. Rs 125 / Piece

The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the modules output is low, lower power consumption; When a finger touches the corresponding position, the modules output is high, if not touched for 12 seconds, it switches to low-power mode. Jog type : the initial state is lower , higher touch , do not touch is lower ( similar touch of a button feature )
This Module can be installed in such as surface plastic, glass of non-metallic materials.In addition to the thin paper ( non-metallic ) covering the surface of the module , as long as the correct location of the touch , you can make hidden in the walls, desktops and other parts of buttons.

Features :

Pulse Sensor

Pulse Sensor

Approx. Rs 400 / Piece(s)

Pulse Sensor Amped is a greatly improved version of the original Pulse Sensor, a plug-and-play heart-rate sensor for Arduino and Arduino compatibles. It can be used by students, artists, athletes, makers, and game & mobile developers who want to easily incorporate live heart-rate data into their projects.

Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. It's noticeably faster and easier to get reliable pulse readings. Pulse Sensor Amped works with either a 3V and 5V Arduino.

Power: 3-5V
Diameter: 16mm
Magnification: 330
LED Wavelength: 609nm

TTP224 4way Touch Sensor

TTP224 4way Touch Sensor

Approx. Rs 125 / Piece

Description

1. Working voltage: 2.4V-5.5V
2. 4 board-level status indicator
3. PCB board size: 35 (mm) x29 (mm)
4. TTP224 capacitive touch sensor IC 4 keys
5. The module can set the output mode, the key output mode, the maximum output time and fast / low power selection

TTP229 16way Touch Sensor Modules

TTP229 16way Touch Sensor Modules

Approx. Rs 175 / Piece

16-Way TTP229 Capacitive Touch Sensor Module uses TTP229 integrated circuit, making it easy to add capacitive touch input to your project. It features 16 sensitive touch pads that make an ideal replacement for the old fashioned keypads

Technical Specifications:-

Tilt Sensor Module

Tilt Sensor Module

Approx. Rs 80 / Piece

Tilt Sensor Module options offered come with on-board LM393 voltage comparator chip as well as photo-activity sensing probe. Supporting 5V/3.3V voltage input, the module also has on-board signal output instructions with option of directly connecting output signal with the microcontroller IO. Further, it comes with option of adjusting sensitivity of the signal detection as well as has reserve line voltage for comparing circuit. We can also offer these in custom configurations as per the working specifications required at client’s end.

Features:

Additional Information:

Ttp226 8way Touch Sensor

Ttp226 8way Touch Sensor

Approx. Rs 150 / Piece

The TTP226 is a touch pad detector IC which offers 8 touch key. The touching detection IC is designed for replacing traditional direct button key with diverse pad size. Capacitive touch allows electronics to sense when your finger is within a few millimetres of a surface to simulate a button “press” just like how the pushbutton works. Capacitive sensing may be used in any place where low to no force human touch sensing is desirable.

Specification:

Vibration Sensor

Vibration Sensor

Approx. Rs 80 / Piece

Product Description:-

This module features an adjustable potentiometer, a vibration sensor, and a LM393 comparator chip to give an adjustable digital output based on the amount of vibration. The potentiometer can be adjusted to both increase and decrease the sensitivity to the desired amount. The module outputs a logic level high (VCC) when it is triggered and a low (GND) when it isn’t. Additionally there is an onboard LED that turns on when the module is triggered.

Specifications:

Water Level Sensor

Water Level Sensor

Approx. Rs 80 / Piece


This is simple and small portable water level/water droplet identification, detection sensor water that have high cost performance. Complete water yield and analog conversion, the output value apply to your custom function. It is low power consumption and high sensitivity. It can make better performance with Arduino 328 controller and sensor relay shield.

Water Sensor water level sensor is an easy-to-use, cost-effective high level/drop recognition sensor, which is obtained by having a series of parallel wires exposed traces measured droplets/water volume in order to determine the water level. Easy to complete water to analog signal conversion and output analog values can be directly read Arduino development board to achieve the level alarm effect.

Specifications
X
Provide Us More Details
Is this Requirement:

One Time Regular

How soon do you want this:

Immediate After 1 month

Purpose of Requirement:

Reselling End Use Raw Material

X

Looking for Sensors For Arduino ?

    country-ico

    We will contact you soon !

    Dileep Jain

    (CEO)

    Rajguru Electronics (I) Private Limited

    Lamington Road, Mumbai, Maharashtra, India

    More Categories

    View All Categories »
    Send SMS
    Contact Us